| Engine Tech & Diagnostics |
| |
Title |
Topic Starter |
Replies |
Views |
Topic Info |
 |
Engine Temp issues/overcooling
Won't warm up
|
Tinker1980 |
16
|
1,347
|
Feb 11 2013, 10:09 AM
Last Post By: Tinker1980
|
 |
Forged Pistons Anybody?
|
Davo53209 |
2
|
662
|
Feb 11 2013, 02:00 AM
Last Post By: Davo53209
|
 |
1.8 Mazada in Chevrolet Metro Mod
|
NastyMoney |
4
|
654
|
Feb 11 2013, 01:23 AM
Last Post By: geopat
|
 |
thread type
plug by oil pressure sending unit
|
dino |
3
|
470
|
Feb 10 2013, 08:31 PM
Last Post By: dino
|
 |
Compression numbers on rebuilt engine
110 psi on rebilt engine
|
Michael_B |
9
|
1,207
|
Feb 10 2013, 06:59 PM
Last Post By: mikeallen2112
|
 |
Engine swap
|
Metro1998 |
4
|
623
|
Feb 10 2013, 03:58 PM
Last Post By: Stubby79
|
 |
Any Tips on cleaning engine with Gunk?
|
heckling7 |
5
|
739
|
Feb 10 2013, 03:29 PM
Last Post By: PTA2PTB
|
 |
G10 GEO / Chevy Metro 1.0 Full Gasket Set (Apex)
Is the engine rebuild kit any good?
|
teddyA |
2
|
528
|
Feb 10 2013, 02:04 PM
Last Post By: Geo Glenn
|
 |
how do I adjust my timing?
|
tanzytinkerz |
4
|
438
|
Feb 10 2013, 01:17 AM
Last Post By: Stiffchezze
|
 |
Oil below my distributor
|
Reista |
2
|
406
|
Feb 9 2013, 07:24 PM
Last Post By: Reista
|
 |
G10 short block?
Just the bottom end
|
Tinker1980 |
2
|
778
|
Feb 9 2013, 05:17 PM
Last Post By: Tinker1980
|
 |
96 1.3L stalled at stop, now won't START!!
new crank seal, wont start now!!
|
gruntvet98 |
11
|
858
|
Feb 9 2013, 03:17 PM
Last Post By: nwgeo
|
 |
Timimg might be off a tooth
slight rumble
|
pdqrunner |
2
|
428
|
Feb 8 2013, 07:26 PM
Last Post By: pdqrunner
|
 |
Replace Intake vs Head Gasket
Need some help deciding which is the offender, probably both
|
alpines |
6
|
1,218
|
Feb 8 2013, 05:26 PM
Last Post By: alpines
|
 |
Rebuild head problem
|
greengeo |
13
|
832
|
Feb 8 2013, 04:11 PM
Last Post By: greengeo
|
 |
Top speed/most FE speed
|
Reista |
12
|
838
|
Feb 8 2013, 12:41 AM
Last Post By: Reista
|
 |
Please help
Left over parts
|
Blaze |
4
|
401
|
Feb 8 2013, 12:37 AM
Last Post By: Bad Bent
|
 |
93 3 cyl Canadian-made, 6 pin diagnostics connector???
Having trouble figuring out which pins to short for timing
|
ATS |
7
|
910
|
Feb 7 2013, 12:21 AM
Last Post By: ATS
|
 |
rebuild problem
|
greengeo |
10
|
673
|
Feb 6 2013, 04:02 PM
Last Post By: Geo Glenn
|
 |
Engine rebuilt compression check, losing oil
4000 miles lose of oil?
|
BrenBren |
11
|
770
|
Feb 6 2013, 01:12 PM
Last Post By: Geo Glenn
|
 |
Light smoke
|
aaronvincent |
3
|
484
|
Feb 6 2013, 11:23 AM
Last Post By: Reista
|
 |
Emissions Test
Geo Metro
|
geometrolsi1.3 |
4
|
399
|
Feb 6 2013, 03:04 AM
Last Post By: Geo Glenn
|
 |
96 1.3 97 1.3
|
Metro1998 |
2
|
424
|
Feb 6 2013, 01:09 AM
Last Post By: Good bye
|
 |
Just replaced lifters/lash adjusters with new and car runs better
Wanted to give update and see how long she will tick
|
cwatkin |
9
|
775
|
Feb 5 2013, 10:13 PM
Last Post By: cwatkin
|
 |
Piston to Cylinder Clearance
Piston Clearance
|
High MX |
8
|
2,752
|
Feb 5 2013, 07:51 PM
Last Post By: Geo Glenn
|
 |
2 problems need diagnosis
egr and missing coolant?
|
nixmixin |
8
|
649
|
Feb 5 2013, 05:35 PM
Last Post By: nixmixin
|
 |
Suggestions Wanted/Geo Metro Rebuild Project
|
Davo53209 |
26
|
1,514
|
Feb 5 2013, 02:38 PM
Last Post By: Davo53209
|
 |
Oil / filter
|
Reista |
13
|
972
|
Feb 5 2013, 07:25 AM
Last Post By: Waldo
|
 |
Changing my timing belt
Does this look right?
|
KickinCamile |
10
|
1,215
|
Feb 5 2013, 06:43 AM
Last Post By: Woodie
|
 |
Air Valve on 92 Metro
Where is it
|
fiberstress |
5
|
582
|
Feb 4 2013, 11:55 PM
Last Post By: Memphis metro
|