Welcome to the all new Geo Metro Forum. We hope you enjoy your visit.You're currently viewing our forum as a guest. This means you are limited to certain areas of the board and there are features you can't use and images you can't see. Registration is simple, fast, and completely free. If you're already a member please log in to your account to access all of our features: Join our community! |
| The Silver One; my 1992 Suzuki Swift Ga | |
|---|---|
| Tweet Topic Started: Feb 8 2015, 10:51 PM (3,103 Views) | |
| Hotrodray1 | Mar 6 2015, 08:20 AM Post #16 |
![]()
Over Educated parts guy
![]()
|
For now I do. I had also thought about a low boost setup on it. I plan on it being my every day driver! So I can work on my gti vert project. |
![]() |
|
| Hotrodray1 | Mar 6 2015, 12:49 PM Post #17 |
![]()
Over Educated parts guy
![]()
|
Got these today from Rockauto.
|
![]() |
|
| brsja | Mar 6 2015, 02:29 PM Post #18 |
![]()
|
I'm confused on these... I see ridges? |
![]() |
|
| Hotrodray1 | Mar 6 2015, 04:58 PM Post #19 |
![]()
Over Educated parts guy
![]()
|
Yea those are slots! |
![]() |
|
| Hydrojim | Mar 6 2015, 06:39 PM Post #20 |
![]()
|
All of the rotor surface is on one plane. The picture just throws things off. |
![]() |
|
| Hotrodray1 | Mar 6 2015, 07:11 PM Post #21 |
![]()
Over Educated parts guy
![]()
|
yes it just has grooves in it that is all. Like gas slotted. |
![]() |
|
| Hotrodray1 | Mar 9 2015, 08:11 PM Post #22 |
![]()
Over Educated parts guy
![]()
|
Ok after the clean up here are some pictures before.![]() ![]() ![]() ![]() ![]() ![]()
|
![]() |
|
| Hotrodray1 | Mar 9 2015, 08:20 PM Post #23 |
![]()
Over Educated parts guy
![]()
|
After![]() ![]() ![]() ![]() ![]() ![]() ![]()
|
![]() |
|
| Hotrodray1 | Mar 9 2015, 08:28 PM Post #24 |
![]()
Over Educated parts guy
![]()
|
Yep a little rust there I think a battery may have went boom in the past! Thank goodness it was just surface rust. A little Dremal tool action fixed it all. Then a little etching primer fixed it all up right. |
![]() |
|
| Hotrodray1 | Mar 9 2015, 08:31 PM Post #25 |
![]()
Over Educated parts guy
![]()
|
Now the difference in the way factory plastic and aftermarket glass headlights look!![]() ![]()
|
![]() |
|
| Turbo Dan-O | Mar 9 2015, 08:32 PM Post #26 |
|
Obsessive Car Detailer
![]()
|
It did happen! Man, that thins was NASTY! Looks good now Ray!
|
![]() |
|
| pvr007 | Mar 9 2015, 09:11 PM Post #27 |
![]()
|
I also cleaned my bay for the first time ever, good old concentrated simple green did the job |
![]() |
|
| Hotrodray1 | Mar 16 2015, 12:11 AM Post #28 |
![]()
Over Educated parts guy
![]()
|
Well after pulling a part the drag motor i had built for a guy to sell. I worked on this!![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() Slowly I am getting it together all new seals output and shifter seal and dust boot. I put driver side axle in and it had a bad clip on end. I had to drive it out it had the wrong retainer clip on it I fixed it. I rebuilt passenger short shaft at goes into trans and attach to passenger axle new bearing and both seals. I also assembled head and shortblock of my 1.3. Then I installed my cylinder head. Not to bad considering i was in hospital last monday diagnosed with Pneumonia. Took almost all week but boy do i feel better. |
![]() |
|
| ZXTjato | Mar 16 2015, 10:18 AM Post #29 |
|
bass heads
![]()
|
I see air conditioner parts. You planning on doing AC? |
![]() |
|
| Hotrodray1 | Mar 16 2015, 11:58 AM Post #30 |
![]()
Over Educated parts guy
![]()
|
Yea after Geos on the gulf! Just dont have enough time to get it done before then! But when I get time it will get a complete new system! trying to decide 134a or old r12 I have both. |
![]() |
|
| 1 user reading this topic (1 Guest and 0 Anonymous) | |
| Go to Next Page | |
| « Previous Topic · Project Forum · Next Topic » |


Welcome to the all new Geo Metro Forum. We hope you enjoy your visit.



















It did happen! Man, that thins was NASTY! Looks good now Ray!










7:24 PM Jul 10